This chapter describes Asynchronous Transfer Mode Network Interface (ATM) messages. For information on message content and how to use the message, refer to the Introduction.
| ATM.001 |
Level: C-INFO
Short Syntax: ATM.001 Create configuration support, nt network ID
Long Syntax: ATM.001 Create configuration support, on network network ID
Description: Trying to create the config_support object.
| ATM.002 |
Level: C-INFO
Short Syntax: ATM.002 Create Timer_master, nt network ID
Long Syntax: ATM.002 Create Timer_master, on network network ID
Description: Trying to create the Timer_master object.
| ATM.003 |
Level: C-INFO
Short Syntax: ATM.003 Create connection manager, nt network ID
Long Syntax: ATM.003 Create connection manager, on network network ID
Description: Trying to create the conn_mgr object.
| ATM.004 |
Level: C-INFO
Short Syntax: ATM.004 Create ilmi_wrapper, nt network ID
Long Syntax: ATM.004 Create ilmi_wrapper, on network network ID
Description: Trying to create the ilmi_wrapper object.
| ATM.005 |
Level: C-INFO
Short Syntax: ATM.005 Create ilmi, nt network ID
Long Syntax: ATM.005 Create ilmi, on network network ID
Description: Trying to create the ilmi (ATM_address_table) object.
| ATM.006 |
Level: C-INFO
Short Syntax: ATM.006 Create ilmi_user, nt network ID
Long Syntax: ATM.006 Create ilmi_user, on network network ID
Description: Trying to create the ilmi_user object.
| ATM.007 |
Level: C-INFO
Short Syntax: ATM.007 Create saal_wrapper, nt network ID
Long Syntax: ATM.007 Create saal_wrapper, on network network ID
Description: Trying to create the saal_wrapper object.
| ATM.008 |
Level: C-INFO
Short Syntax: ATM.008 Create qsaal, nt network ID
Long Syntax: ATM.008 Create qsaal, on network network ID
Description: Trying to create the qsaal object.
| ATM.009 |
Level: C-INFO
Short Syntax: ATM.009 Create signalling (Q93B_protocol), nt network ID
Long Syntax: ATM.009 Create signalling (Q93B_protocol), on network network ID
Description: Trying to create the Q93B_protocol (Signalling) object.
| ATM.010 |
Level: C-INFO
Short Syntax: ATM.010 Calling object_addrs_avail, nt network ID
Long Syntax: ATM.010 Calling object_addrs_avail, on network network ID
Description: Calling object_addrs_avail for all created objects.
| ATM.011 |
Level: C-INFO
Short Syntax: ATM.011 Starting ilmi_wrapper, nt network ID
Long Syntax: ATM.011 Starting ilmi_wrapper, on network network ID
Description: Calling ilmi_wrapper->start.
| ATM.012 |
Level: C-INFO
Short Syntax: ATM.012 Starting ilmi, nt network ID
Long Syntax: ATM.012 Starting ilmi, on network network ID
Description: Calling ilmi->start.
| ATM.013 |
Level: UI-ERROR
Short Syntax: ATM.013 Start of ilmi_wrapper failed, nt network ID, rc retcode
Long Syntax: ATM.013 Start of ilmi_wrapper failed, on network network ID, return code = retcode
Description: ilmi_wrapper->start failed.
| ATM.014 |
Level: UI-ERROR
Short Syntax: ATM.014 Start of ilmi failed, nt network ID, rc retcode
Long Syntax: ATM.014 Start of ilmi failed, on network network ID, return code = retcode
Description: ilmi->start failed.
| ATM.015 |
Level: UI-ERROR
Short Syntax: ATM.015 Creation of configuration support failed, nt network ID, rc retcode
Long Syntax: ATM.015 Creation of configuration support failed, on network network ID, return code = retcode
Description: Create config_support failed.
| ATM.016 |
Level: UI-ERROR
Short Syntax: ATM.016 Creation of Timer_master failed, nt network ID, rc retcode
Long Syntax: ATM.016 Creation of Timer_master failed, on network network ID, return code = retcode
Description: Create Timer_master failed.
| ATM.017 |
Level: UI-ERROR
Short Syntax: ATM.017 Creation of connection manager failed, nt network ID, rc retcode
Long Syntax: ATM.017 Creation of connection manager failed, on network network ID, return code = retcode
Description: Create conn_mgr failed.
| ATM.018 |
Level: UI-ERROR
Short Syntax: ATM.018 Creation of ilmi_wrapper failed, nt network ID, rc retcode
Long Syntax: ATM.018 Creation of ilmi_wrapper failed, on network network ID, return code = retcode
Description: Create ilmi_wrapper failed.
| ATM.019 |
Level: UI-ERROR
Short Syntax: ATM.019 Creation of ilmi failed, nt network ID, rc retcode
Long Syntax: ATM.019 Creation of ilmi failed, on network network ID, return code = retcode
Description: Create ilmi failed.
| ATM.020 |
Level: UI-ERROR
Short Syntax: ATM.020 Creation of ilmi_user failed, nt network ID
Long Syntax: ATM.020 Creation of ilmi_user failed, on network network ID
Description: Create ilmi_user failed.
| ATM.021 |
Level: UI-ERROR
Short Syntax: ATM.021 Creation of saal_wrapper failed, nt network ID, rc retcode
Long Syntax: ATM.021 Creation of saal_wrapper failed, on network network ID, return code = retcode
Description: Create saal_wrapper failed.
| ATM.022 |
Level: UI-ERROR
Short Syntax: ATM.022 Creation of qsaal failed, nt network ID, rc retcode
Long Syntax: ATM.022 Creation of qsaal failed, on network network ID, return code = retcode
Description: Create qsaal failed.
| ATM.023 |
Level: UI-ERROR
Short Syntax: ATM.023 Creation of signalling (Q93B_protocol) failed, nt network ID, rc retcode
Long Syntax: ATM.023 Creation of signalling (Q93B_protocol) failed, on network network ID, return code = retcode
Description: Create Q93B_protocol failed.
| ATM.024 |
Level: UI-ERROR
Short Syntax: ATM.024 Bad inbound control frame discarded, handle = conn_handle nt network ID
Long Syntax: ATM.024 Bad inbound control frame discarded, handle = conn_handle, on network network ID
Description: Bad inbound control frame
| ATM.025 |
Level: C-INFO
Short Syntax: ATM.025 Frame xmit by net_dsio, handle = conn_handle nt network ID
Long Syntax: ATM.025 Frame transmitted using net_dsio, handle = conn_handle, on network network ID
Description: A frame has been transmitted on the ATM interface, using net_dsio.
| ATM.026 |
Level: UI-ERROR
Short Syntax: ATM.026 Inbound frame discarded, handle = conn_handle nt network ID, rc stat
Long Syntax: ATM.026 Inbound frame discarded, handle = conn_handle, on network network ID, status = stat
Description: Bad status in iorb
| ATM.027 |
Level: UI-ERROR
Short Syntax: ATM.027 Outbound frame not sent, handle = conn_handle nt network ID, rc retcode
Long Syntax: ATM.027 Outbound frame not sent, handle = conn_handle, on network network ID, return code = retcode
Description: Bad status from netout
| ATM.028 |
Level: UI-ERROR
Short Syntax: ATM.028 Device Driver User Registration Failed, handle = conn_handle nt network ID, rc stat
Long Syntax: ATM.028 Device Driver User Registration Failed, handle = conn_handle, on network network ID, status = stat
Description: atmcharm_init User Registration Failed
| ATM.029 |
Level: UI-ERROR
Short Syntax: ATM.029 Device Driver Wrap User Registration Failed, handle = conn_handle nt network ID, rc rc
Long Syntax: ATM.029 Device Driver Wrap User Registration Failed, handle = conn_handle, on network network ID, status = rc
Description: atmcharm_init Wrap User Registration Failed
| ATM.030 |
Level: UI-ERROR
Short Syntax: ATM.030 ERROR opening Frame SAP, handle = conn_handle nt network ID, rc stat
Long Syntax: ATM.030 ERROR opening Frame SAP, handle = conn_handle, on network network ID, status = stat
Description: Couldn't open Frame SAP
| ATM.031 |
Level: UI-ERROR
Short Syntax: ATM.031 ERROR opening data path for ILMI, handle = conn_handle nt network ID, rc stat
Long Syntax: ATM.031 ERROR opening data path for ILMI, handle = conn_handle, on network network ID, status = stat
Description: Couldn't open data path for ILMI
| ATM.032 |
Level: UI-ERROR
Short Syntax: ATM.032 ERROR opening Wrap Frame SAP, handle = conn_handle nt network ID, rc rc
Long Syntax: ATM.032 ERROR opening Wrap Frame SAP, handle = conn_handle, on network network ID, status = rc
Description: Couldn't open Wrap Frame SAP
| ATM.033 |
Level: UI-ERROR
Short Syntax: ATM.033 ERROR creating objects, handle = conn_handle nt network ID, rc rc
Long Syntax: ATM.033 ERROR creating objects, handle = conn_handle, on network network ID, status = rc
Description: Couldn't create objects (SVC, ILMI, etc.)
| ATM.034 |
Level: UI-ERROR
Short Syntax: ATM.034 Inbound frame discarded, handle = conn_handle nt network ID, cnt i_bxfr
Long Syntax: ATM.034 Inbound frame discarded, handle = conn_handle, on network network ID, count = i_bxfr
Description: Bad byte count in iorb
| ATM.035 |
Level: C-INFO
Short Syntax: ATM.035 Function function_name called, nt network ID
Long Syntax: ATM.035 Function function_name called, on network network ID
Description: ATM function called
| ATM.036 |
Level: UI-ERROR
Short Syntax: ATM.036 Could not stop objects, nt network ID, rc rc
Long Syntax: ATM.036 Could not stop objects, on network network ID, return code = rc
Description: Error stopping the objects
| ATM.037 |
Level: UI-ERROR
Short Syntax: ATM.037 Connection handle is NULL, nt network ID
Long Syntax: ATM.037 Connection handle is NULL, on network network ID
Description: conn_handle is NULL
| ATM.038 |
Level: UI-ERROR
Short Syntax: ATM.038 Unable to get buffers, nt network ID
Long Syntax: ATM.038 Unable to get buffers on network network ID
Description: Could not get a buffer
| ATM.039 |
Level: UI-ERROR
Short Syntax: ATM.039 Connect ioctl failed , nt network ID vpi/vci vpi/ vci
Long Syntax: ATM.039 Connect ioctl failed , nt network ID vpi/vci vpi/ vci
Description: Connect ioctl failed
| ATM.040 |
Level: UI-ERROR
Short Syntax: ATM.040 Could not start objects, nt network ID, rc rc
Long Syntax: ATM.040 Could not start objects, on network network ID, return code = rc
Description: Error starting the objects
| ATM.041 |
Level: UI-ERROR
Short Syntax: ATM.041 Invalid max SDU size, nt network ID, SDU sz rate
Long Syntax: ATM.041 Invalid max SDU size, on network network ID, max SDU size = rate
Description: ATM net handler was passed invalid max SDU size for connection
| ATM.042 |
Level: UI-ERROR
Short Syntax: ATM.042 Invalid peak cell rate, nt network ID, pk rate rate
Long Syntax: ATM.042 Invalid peak cell rate, on network network ID, peak cell rate = rate
Description: ATM net handler was passed invalid peak cell rate for connection
| ATM.043 |
Level: UI-ERROR
Short Syntax: ATM.043 Invalid sustainable cell rate, nt network ID, sustn rate rate
Long Syntax: ATM.043 Invalid sustainable cell rate, on network network ID, sustainable cell rate = rate
Description: ATM net handler was passed invalid sustainable cell rate for connection
| ATM.044 |
Level: UI-ERROR
Short Syntax: ATM.044 Invalid max burst size, nt network ID, brst sz rate
Long Syntax: ATM.044 Invalid max burst size, on network network ID, max burst size = rate
Description: ATM net handler was passed invalid max burst size for connection
| ATM.045 |
Level: UI-ERROR
Short Syntax: ATM.045 API, invalid net number, nt network ID, dev devNum
Long Syntax: ATM.045 API called with invalid net number, on network network ID, devNum devNum
Description: atmUserRegistration called with invalid devNum
| ATM.046 |
Level: UI-ERROR
Short Syntax: ATM.046 API call failed, no memory, nt network ID
Long Syntax: ATM.046 API call failed, no memory, on network network ID
Description: ATM API call failed, no memory available
| ATM.047 |
Level: UI-ERROR
Short Syntax: ATM.047 Get UNI version ILMI failed, nt network ID, rc rc
Long Syntax: ATM.047 Get UNI Version ILMI failed, on network network ID, return code = rc
Description: atmGetUniVersion ILMI returned get_uni_version_wrap with bad return
| ATM.048 |
Level: UI-ERROR
Short Syntax: ATM.048 API, invalid user handle, userHandle
Long Syntax: ATM.048 API called with invalid user handle, userHandle
Description: atmUserRegistration called with invalid user handle
| ATM.049 |
Level: CI-ERROR
Short Syntax: ATM.049 API call failed, net down, nt network ID
Long Syntax: ATM.049 API call failed, network down, on network network ID
Description: ATM API call failed, network is down
| ATM.050 |
Level: C-INFO
Short Syntax: ATM.050 Address activation ILMI successful, nt network ID, rc rc
Long Syntax: ATM.050 ATM address activation ILMI successful, on network network ID, return code = rc
Description: atmAddrActivation ILMI returned alloc_addr_wrap with good return
| ATM.051 |
Level: UI-ERROR
Short Syntax: ATM.051 Address activation ILMI failed, nt network ID, rc rc
Long Syntax: ATM.051 ATM address activation ILMI failed, on network network ID, return code = rc
Description: atmAddrActivation ILMI returned alloc_addr_wrap with bad return
| ATM.052 |
Level: C-INFO
Short Syntax: ATM.052 Sharing ESI/Selector, nt network ID, addr addr
Long Syntax: ATM.052 Sharing ESI/Selector, on network network ID, addr addr
Description: atmAddrActivation providing sharing of the ATM address
| ATM.053 |
Level: C-INFO
Short Syntax: ATM.053 conn_mgr dstrc ntrd, nt network ID
Long Syntax: ATM.053 Connection Manager destructor entered, on network network ID
Description: Connection Manager destructor entered
| ATM.054 |
Level: UI-ERROR
Short Syntax: ATM.054 API, invalid address handle, nt network ID, hndl handle
Long Syntax: ATM.054 API called with invalid address handle, on network network ID, handle = handle
Description: atmAddrDeactivation called with invalid address handle
| ATM.055 |
Level: UI-ERROR
Short Syntax: ATM.055 Address deactivation ILMI failed, nt network ID, hndl handle rc rc
Long Syntax: ATM.055 ATM address deactivation ILMI failed, on network network ID, handle = handle, return code = rc
Description: atmAddrDeactivation ILMI returned free_addr_handle_wrap with bad return
| ATM.056 |
Level: UI-ERROR
Short Syntax: ATM.056 Get address by handle ILMI failed, nt network ID, hndl handle rc rc
Long Syntax: ATM.056 Get ATM address by handle ILMI failed, on network network ID, handle = handle, return code = rc
Description: atmGetAddrByHandle ILMI returned get_atm_addr_wrap with bad return
| ATM.057 |
Level: C-INFO
Short Syntax: ATM.057 Get UNI version ILMI successful, nt network ID, rc rc
Long Syntax: ATM.057 Get UNI Version ILMI successful, on network network ID, return code = rc
Description: atmGetUniVersion ILMI returned get_uni_version_wrap with good return
| ATM.058 |
Level: C-INFO
Short Syntax: ATM.058 Get LECS address ILMI successful, nt network ID, rc rc
Long Syntax: ATM.058 Get LECS address ILMI successful, on network network ID, return code = rc
Description: atmGetLecsAddr ILMI returned get_lecs_list_wrap with good return
| ATM.059 |
Level: UI-ERROR
Short Syntax: ATM.059 Get LECS address ILMI failed, nt network ID, rc rc
Long Syntax: ATM.059 Get LECS address ILMI failed, on network network ID, return code = rc
Description: atmGetLecsAddr ILMI returned get_lecs_list_wrap with bad return
| ATM.060 |
Level: UI-ERROR
Short Syntax: ATM.060 call SAP already open, nt network ID hndl handle
Long Syntax: ATM.060 call SAP already open for this user, network network ID, SAP handle = handle
Description: call SAP already open for this user
| ATM.061 |
Level: UI-ERROR
Short Syntax: ATM.061 max call SAPs exceeded, nt network ID
Long Syntax: ATM.061 max call SAPs exceeded, network network ID
Description: Maximum call SAPs already opened.
| ATM.062 |
Level: UI-ERROR
Short Syntax: ATM.062 bad PID count, nt network ID cnt count
Long Syntax: ATM.062 bad PID count, network network ID, count = count
Description: PID count in PID list out of range
| ATM.063 |
Level: UI-ERROR
Short Syntax: ATM.063 bad PID, nt network ID PID PID
Long Syntax: ATM.063 bad PID, network network ID, PID = PID
Description: Invalid PID in PID list
| ATM.064 |
Level: UI-ERROR
Short Syntax: ATM.064 Conn mgr register caller failed, nt network ID, rc rc
Long Syntax: ATM.064 Connection manager register caller failed, on network network ID, return code = rc
Description: Connection Manager call to reg_caller_wrap failed.
| ATM.065 |
Level: UI-ERROR
Short Syntax: ATM.065 API, invalid call SAP hndl, nt network ID, hndl handle
Long Syntax: ATM.065 API received invalid call SAP handle, on network network ID, handle = handle
Description: Invalid call SAP handle passed to API
| ATM.066 |
Level: C-INFO
Short Syntax: ATM.066 API, placing call, nt network ID, addr address
Long Syntax: ATM.066 API, placing call, on network network ID, ATM address = address
Description: Placing a call to a given address
| ATM.067 |
Level: UI-ERROR
Short Syntax: ATM.067 API, place call failed, nt network ID, hndl handle, addr address, rc rc
Long Syntax: ATM.067 API, place call failed, on network network ID, handle = handle, ATM address = address, return code = rc
Description: Placing a call to a given address failed
| ATM.068 |
Level: C-INFO
Short Syntax: ATM.068 API, adding leaf, nt network ID, addr address, conn hndl = handle
Long Syntax: ATM.068 API, adding leaf, on network network ID, ATM address = address, conn handle = handle,
Description: Adding a leaf to a multipoint call
| ATM.069 |
Level: UI-ERROR
Short Syntax: ATM.069 API, add leaf failed, nt network ID, hndl handle, addr address, rc rc
Long Syntax: ATM.069 API, add leaf failed, on network network ID, handle = handle, ATM address = address, return code = rc
Description: Adding a leaf to a multipoint call failed
| ATM.070 |
Level: C-INFO
Short Syntax: ATM.070 API, hangup leaf, nt network ID, conn hndl connHandle, leaf hndl leafHandle
Long Syntax: ATM.070 API, hangup leaf, on network network ID, conn handle = connHandle, leaf handle = leafHandle
Description: Hanging up a leaf
| ATM.071 |
Level: C-INFO
Short Syntax: ATM.071 API, recv call ack, nt network ID, conn hndl connHandle
Long Syntax: ATM.071 API, receive call ack, on network network ID, conn handle = connHandle
Description: Receive call ack
| ATM.072 |
Level: C-INFO
Short Syntax: ATM.072 API, hangup call, nt network ID, conn hndl connHandle
Long Syntax: ATM.072 API, hangup call, on network network ID, conn handle = connHandle
Description: Hanging up a call
| ATM.073 |
Level: UI-ERROR
Short Syntax: ATM.073 API, invalid frame SAP type, nt network ID, type type
Long Syntax: ATM.073 API called with invalid frame SAP type, on network network ID, type = type
Description: Invalid frame SAP type passed to API
| ATM.074 |
Level: UI-ERROR
Short Syntax: ATM.074 API, invalid frame SAP hndl, nt network ID, hndl handle
Long Syntax: ATM.074 API called with invalid frame SAP handle, on network network ID, handle = handle
Description: Invalid frame SAP handle passed to API
| ATM.075 |
Level: UI-ERROR
Short Syntax: ATM.075 API, invalid VCC hndl, nt network ID, hndl handle
Long Syntax: ATM.075 API called with invalid VCC handle, on network network ID, handle = handle
Description: Invalid VCC handle passed to API
| ATM.076 |
Level: UI-ERROR
Short Syntax: ATM.076 API, invalid MAC offset, nt network ID, offset offset
Long Syntax: ATM.076 API called with invalid MAC address offset, on network network ID, offset = offset
Description: Invalid MAC address offset passed to API
| ATM.077 |
Level: UI-ERROR
Short Syntax: ATM.077 API, invalid VCC grp hndl, nt network ID, grp hndl handle
Long Syntax: ATM.077 API called with invalid VCC group handle, on network network ID, group handle = handle
Description: Invalid VCC group handle passed to API
| ATM.078 |
Level: UI-ERROR
Short Syntax: ATM.078 API, VCC already in grp, nt network ID, vcc hndl vcchandle, grp hndl grphandle
Long Syntax: ATM.078 API, VCC already in group, on network network ID, vcc handle = vcchandle, group handle = grphandle
Description: Trying to add a VCC to a group it is already a part of
| ATM.079 |
Level: UI-ERROR
Short Syntax: ATM.079 API, VCC not in grp, nt network ID, vcc hndl vcchandle, grp hndl grphandle
Long Syntax: ATM.079 API, VCC not in group, on network network ID, vcc handle = vcchandle, group handle = grphandle
Description: VCC not in this group
| ATM.080 |
Level: UI-ERROR
Short Syntax: ATM.080 API, MAC already mapped, nt network ID, vcc hndl vcchandle, grp hndl grphandle, MAC MACaddr
Long Syntax: ATM.080 API, MAC already mapped, on network network ID, vcc handle = vcchandle, group handle = grphandle, MAC address MACaddr
Description: Trying to map a MAC address to a group it is already mapped to
| ATM.081 |
Level: UI-ERROR
Short Syntax: ATM.081 API, MAC not mapped, nt network ID, vcc hndl vcchandle, grp hndl grphandle, MAC MACaddr
Long Syntax: ATM.081 API, MAC not mapped, on network network ID, vcc handle = vcchandle, group handle = grphandle, MAC address MACaddr
Description: Trying to unmap a MAC address to a group it is not mapped to
| ATM.082 |
Level: C-INFO
Short Syntax: ATM.082 addr state change, nt network ID, addr address, state = state
Long Syntax: ATM.082 ATM address state change, on network network ID, ATM address = address, state= state,
Description: Address state change
| ATM.083 |
Level: UI-ERROR
Short Syntax: ATM.083 Connection manager start failed, nt network ID, rc retcode
Long Syntax: ATM.083 Connection manager start failed, on network network ID, return code = retcode
Description: Connection Manager start failed.
| ATM.084 |
Level: UI-ERROR
Short Syntax: ATM.084 SAAL wrapper start failed, nt network ID, rc retcode
Long Syntax: ATM.084 SAAL wrapper start failed, on network network ID, return code = retcode
Description: SAAL wrapper start failed.
| ATM.085 |
Level: UI-ERROR
Short Syntax: ATM.085 SAAL start failed, nt network ID, rc retcode
Long Syntax: ATM.085 SAAL start failed, on network network ID, return code = retcode
Description: SAAL start failed.
| ATM.086 |
Level: UI-ERROR
Short Syntax: ATM.086 SVC start failed, nt network ID, rc retcode
Long Syntax: ATM.086 SVC start failed, on network network ID, return code = retcode
Description: SVC start failed.
| ATM.087 |
Level: C-INFO
Short Syntax: ATM.087 Conn mgr stopped, nt network ID
Long Syntax: ATM.087 Connection Manager stopped, on network network ID
Description: Connection Manager stop entered
| ATM.088 |
Level: P_TRACE
Short Syntax: ATM.088 Trace ATM frame.
Long Syntax: ATM.088 Trace ATM frame.
Description: ATM frame packet tracing.
| ATM.089 |
Level: UI-ERROR
Short Syntax: ATM.089 Conn mgr place call failed, nt network ID, rc retcode
Long Syntax: ATM.089 Connection manager place call failed, on network network ID, rc = retcode
Description: Conn Mgr place call failed.
| ATM.090 |
Level: U-INFO
Short Syntax: ATM.090 Call setup failed, SAAL not up yet, nt network ID
Long Syntax: ATM.090 Call setup failed, SAAL not up yet, on network network ID
Description: Call set-up failed because the SAAL was not established yet.
| ATM.091 |
Level: UI-ERROR
Short Syntax: ATM.091 Conn handle in use, nt network ID, hdnl handle
Long Syntax: ATM.091 SVC thinks conn handle is in use, on network network ID, handle = handle
Description: Call set-up failed because the SVC thought the conn handle was in use.
| ATM.092 |
Level: UI-ERROR
Short Syntax: ATM.092 Invalid conn handle, nt network ID, hdnl handle
Long Syntax: ATM.092 Invalid conn handle, no entry in connection table, on network network ID, handle = handle
Description: Call set-up failed because the conn handle points to a NULL entry.
| ATM.093 |
Level: UI-ERROR
Short Syntax: ATM.093 Place call ack failed, nt network ID, rc retcode, hdnl handle, vpi vpi, vci vci
Long Syntax: ATM.093 Place call ack failed, on network network ID, rc = retcode, handle = handle, vpi = vpi, vci = vci
Description: Place call ack failed
| ATM.094 |
Level: UE-ERROR
Short Syntax: ATM.094 Receive call failed, no such caller, nt network ID, hdnl handle, vpi vpi, vci vci
Long Syntax: ATM.094 Receive call failed, no such caller, on network network ID, handle = handle, vpi = vpi, vci = vci
Description: No caller found matching call parms.
| ATM.095 |
Level: UE-ERROR
Short Syntax: ATM.095 call rjct, nt network ID, rc retcode, hdnl handle, vpi vpi, vci vci
Long Syntax: ATM.095 Call rejected, on network network ID, rc = retcode, handle = handle, vpi = vpi, vci = vci
Description: Called party rejected call.
| ATM.096 |
Level: C-INFO
Short Syntax: ATM.096 Call accepted, nt network ID, rc retcode, hdnl handle, vpi vpi, vci vci
Long Syntax: ATM.096 Call accepted, on network network ID, rc = retcode, handle = handle, vpi = vpi, vci = vci
Description: Called party accepted call.
| ATM.097 |
Level: C-INFO
Short Syntax: ATM.097 Receive call ack, nt network ID, rc retcode, hdnl handle
Long Syntax: ATM.097 Receive call ack, on network network ID, rc = retcode, handle = handle
Description: Called party accepts or rejects call.
| ATM.098 |
Level: UI-ERROR
Short Syntax: ATM.098 Bad cnfg prm, n_int interface, rc retcode, prm parm
Long Syntax: ATM.098 Bad configuration parm, n_int = interface, rc = retcode, parm = parm
Description: Conn Mgr attempt to read configuration parameter failed.
| ATM.099 |
Level: UI-ERROR
Short Syntax: ATM.099 Conn mgr, no memory, n_int interface, pnt point
Long Syntax: ATM.099 Connection Manager, no memory, n_int = interface, trace point = point
Description: Connection Manager could not get memory to initialize
| ATM.100 |
Level: C-INFO
Short Syntax: ATM.100 Conn mgr adding leaf, nt network ID, hndl handle
Long Syntax: ATM.100 Connection Manager adding leaf, on network network ID, handle = handle
Description: Connection Manager add leaf entered
| ATM.101 |
Level: UI-ERROR
Short Syntax: ATM.101 Invld conn hndl, not in connect tbl, nt network ID, hdnl handle, func function_name
Long Syntax: ATM.101 Invalid conn handle, no entry in connection table, on network network ID, handle = handle, function function_name
Description: The conn handle points to a NULL entry.
| ATM.102 |
Level: UI-ERROR
Short Syntax: ATM.102 Invld conn hndl, free connection, nt network ID, hdnl handle, func function_name
Long Syntax: ATM.102 Invalid conn handle, free connection, on network network ID, handle = handle, function = function_name
Description: The connection handle points to a inactive entry.
| ATM.103 |
Level: UI-ERROR
Short Syntax: ATM.103 No leaf handle available, nt network ID, hdnl handle
Long Syntax: ATM.103 No leaf handle available, on network network ID, conn handle = handle
Description: Could not get leaf handle
| ATM.104 |
Level: UI-ERROR
Short Syntax: ATM.104 Add leaf handle failed, nt network ID, hdnl handle, rc retcode
Long Syntax: ATM.104 Add leaf handle failed, on network network ID, conn handle = handle, rc = retcode
Description: Add leaf handle failed
| ATM.105 |
Level: C-INFO
Short Syntax: ATM.105 Conn mgr add leaf ack, nt network ID, hndl handle
Long Syntax: ATM.105 Connection Manager add leaf ack, on network network ID, handle = handle
Description: Connection Manager add leaf ack entered
| ATM.106 |
Level: C-INFO
Short Syntax: ATM.106 Conn mgr registering caller, nt network ID
Long Syntax: ATM.106 Connection Manager registering caller, on network network ID
Description: Connection Manager register_caller entered
| ATM.107 |
Level: UI-ERROR
Short Syntax: ATM.107 Max callers exceeded, nt network ID
Long Syntax: ATM.107 Max callers exceeded, on network network ID
Description: Caller tried to register, maximum callers already registered.
| ATM.108 |
Level: UI-ERROR
Short Syntax: ATM.108 dup cllr PID, nt network ID
Long Syntax: ATM.108 Duplicate caller PID, on network network ID
Description: A caller tried to register with the same PID and address as an existing caller.
| ATM.109 |
Level: UI-ERROR
Short Syntax: ATM.109 dup cllr addr, nt network ID
Long Syntax: ATM.109 Duplicate caller address, on network network ID
Description: A caller tried to register with the same address as an existing caller.
| ATM.110 |
Level: C-INFO
Short Syntax: ATM.110 Conn mgr deregistering caller, nt network ID
Long Syntax: ATM.110 Connection Manager deregistering caller, on network network ID
Description: Connection Manager deregister_caller entered
| ATM.111 |
Level: C-INFO
Short Syntax: ATM.111 Conn mgr disconnecting call, nt network ID, hndl handle
Long Syntax: ATM.111 Connection Manager disconnecting call, on network network ID, handle = handle
Description: Connection Manager disconnect_call entered
| ATM.112 |
Level: C-INFO
Short Syntax: ATM.112 rmv cnxn, SVC err, nt network ID, hndl handle
Long Syntax: ATM.112 Conn Mgr removing connection, SVC error, on network network ID, handle = handle
Description: SVC got a conn handle, found an error, and is giving it back
| ATM.113 |
Level: C-INFO
Short Syntax: ATM.113 Conn mgr reporting failure, nt network ID, hndl handle
Long Syntax: ATM.113 Connection Manager reporting failure to caller, on network network ID, handle = handle
Description: Connection Manager report_failure_to_Caller entered
| ATM.114 |
Level: C-INFO
Short Syntax: ATM.114 Conn mgr removing connection, nt network ID, hndl handle
Long Syntax: ATM.114 Connection Manager removing connection, on network network ID, handle = handle
Description: Connection Manager remove connection entered
| ATM.115 |
Level: C-INFO
Short Syntax: ATM.115 Conn mgr disconnecting leaf, nt network ID, hndl handle
Long Syntax: ATM.115 Connection Manager disconnecting leaf, on network network ID, handle = handle
Description: Connection Manager disconnect_leaf entered
| ATM.116 |
Level: C-INFO
Short Syntax: ATM.116 Conn mgr getting conn hndl, nt network ID
Long Syntax: ATM.116 Connection Manager getting conn handle, on network network ID
Description: Connection Manager get_conn_handle entered
| ATM.117 |
Level: UI-ERROR
Short Syntax: ATM.117 no conn handles, nt network ID
Long Syntax: ATM.117 All connection handles in use, on network network ID
Description: No free conn handles
| ATM.118 |
Level: UI-ERROR
Short Syntax: ATM.118 no mem conn obj, nt network ID
Long Syntax: ATM.118 No memory for connection object, on network network ID
Description: No memory for connection object
| ATM.119 |
Level: C-INFO
Short Syntax: ATM.119 Conn mgr hanging up call, nt network ID, hndl handle
Long Syntax: ATM.119 Connection Manager hanging up call, on network network ID, handle = handle
Description: Connection Manager hang_up_call entered
| ATM.120 |
Level: C-INFO
Short Syntax: ATM.120 conn_mgr hanging up leaf, nt network ID, hndl handle
Long Syntax: ATM.120 Connection Manager hanging up leaf, on network network ID, handle = handle
Description: Connection Manager hang_up_leaf entered
| ATM.121 |
Level: UI-ERROR
Short Syntax: ATM.121 Hang up leaf failed, nt network ID, rc retcode
Long Syntax: ATM.121 SVC hang up leaf failed, on network network ID, rc = retcode
Description: SVC hang_up_leaf failed
| ATM.122 |
Level: C-INFO
Short Syntax: ATM.122 Hang up leaf success, nt network ID, rc retcode
Long Syntax: ATM.122 SVC hang up leaf success, on network network ID, rc = retcode
Description: SVC hang_up_leaf successful
| ATM.123 |
Level: C-INFO
Short Syntax: ATM.123 Conn mgr placing call, nt network ID
Long Syntax: ATM.123 Connection Manager placing call, on network network ID
Description: Connection Manager place_call entered
| ATM.124 |
Level: UI-ERROR
Short Syntax: ATM.124 Max calls exceeded, nt network ID
Long Syntax: ATM.124 Max calls exceeded, on network network ID
Description: Caller tried to place call, maximum calls already placed.
| ATM.125 |
Level: UI-ERROR
Short Syntax: ATM.125 cllr not reg, nt network ID, hndl handle
Long Syntax: ATM.125 Caller not registered, on network network ID, handle = handle
Description: Caller not registered.
| ATM.126 |
Level: C-INFO
Short Syntax: ATM.126 Conn mgr place call ack, nt network ID
Long Syntax: ATM.126 Connection Manager place call ack, on network network ID
Description: Connection Manager place_call_ack entered
| ATM.127 |
Level: C-INFO
Short Syntax: ATM.127 Conn mgr processing received call, nt network ID
Long Syntax: ATM.127 Connection Manager processing received call, on network network ID
Description: Connection Manager process_receive_call entered
| ATM.128 |
Level: UE-ERROR
Short Syntax: ATM.128 Cllee not reg, nt network ID, hndl handle
Long Syntax: ATM.128 Callee not registered, on network network ID, conn handle = handle
Description: Callee not registered.
| ATM.129 |
Level: C-INFO
Short Syntax: ATM.129 Callee found, nt network ID, cllr caller, cnxn handle
Long Syntax: ATM.129 Callee found, on network network ID, caller = caller, conn_handle = handle
Description: Callee found.
| ATM.130 |
Level: C-INFO
Short Syntax: ATM.130 Conn mgr finding caller id, nt network ID
Long Syntax: ATM.130 Connection Manager finding caller id, on network network ID
Description: Connection Manager find_caller_id entered
| ATM.131 |
Level: UI-ERROR
Short Syntax: ATM.131 Addr not found, nt network ID,addr handle
Long Syntax: ATM.131 Address not found by ILMI, on network network ID, address handle = handle
Description: Address not found by ILMI.
| ATM.132 |
Level: C-INFO
Short Syntax: ATM.132 Callee found, nt network ID,hndl handle
Long Syntax: ATM.132 Callee found, on network network ID, caller handle = handle
Description: Callee found
| ATM.133 |
Level: UE-ERROR
Short Syntax: ATM.133 cllee not reg, nt network ID, hndl handle
Long Syntax: ATM.133 Callee not registered, on network network ID, address handle = handle
Description: Callee not registered.
| ATM.134 |
Level: UI-ERROR
Short Syntax: ATM.134 Conn handle NULL, nt network ID
Long Syntax: ATM.134 Connection handle NULL, on network network ID
Description: Connection handle in iorb is NULL.
| ATM.135 |
Level: UI-ERROR
Short Syntax: ATM.135 ILMI ptr NULL, nt network ID
Long Syntax: ATM.135 ILMI wrapper function called, ILMI pointer is NULL, on network network ID
Description: ILMI wrapper function called, ILMI pointer is NULL.
| ATM.136 |
Level: UI-ERROR
Short Syntax: ATM.136 ILMI wrap ptr NULL, nt network ID
Long Syntax: ATM.136 ILMI wrapper function called, ILMI wrapper pointer is NULL, on network network ID
Description: ILMI wrapper function called, ILMI wrapper pointer is NULL.
| ATM.137 |
Level: UI-ERROR
Short Syntax: ATM.137 ERROR opening data path for SVC, handle = user_handle nt network ID, rc stat
Long Syntax: ATM.137 ERROR opening data path for SVC, handle = user_handle, on network network ID, status = stat
Description: Couldn't open data path for SVC
| ATM.138 |
Level: UI-ERROR
Short Syntax: ATM.138 Unknown adapter type, nt network ID, type adapter_type
Long Syntax: ATM.138 Unknown adapter type, on network network ID, adapter type = adapter_type
Description: The adapter returned an unknown adapter type.
| ATM.139 |
Level: UI-ERROR
Short Syntax: ATM.139 Slftst called, nt network ID down
Long Syntax: ATM.139 Selftest called, but network network ID is down
Description: Self-test was called, but the adapter is down
| ATM.140 |
Level: CE-ERROR
Short Syntax: ATM.140 Prefix removed, nt network ID
Long Syntax: ATM.140 The switch removed its prefix on network network ID
Description: The ATM switch removed its prefix.
| ATM.141 |
Level: UE-ERROR
Short Syntax: ATM.141 Cnfgd spd not adapter spd, nt network ID, cnfg config, adapter adapter
Long Syntax: ATM.141 Configured speed different from adapter on network network ID, config speed = config, adapter speed = adapter
Description: The adapter speed is differnet from the configured speed
| ATM.142 |
Level: UI-ERROR
Short Syntax: ATM.142 Bad VCC handle, nt network ID, hdnl= handle
Long Syntax: ATM.142 Bad VCC handle, on network network ID, handle = handle
Description: The device driver passed a bad VCC handle to the net handler.
| ATM.143 |
Level: C-INFO
Short Syntax: ATM.143 VCC hdnl, nt network ID, hdnl= handle, VPI= vpi,VCI= vci
Long Syntax: ATM.143 VCC handle passed to device driver, on network network ID, handle = handle, VPI = vpi, VCI = vci
Description: The net handler passed a handle to the device driver for this VPI/VCI.
| ATM.144 |
Level: UI-ERROR
Short Syntax: ATM.144 No bfr for disc, nt network ID, VPI= vpi,VCI= vci
Long Syntax: ATM.144 No buffer for disconnect, on network network ID, VPI = vpi, VCI = vci
Description: No buffer was available to disconnect a VCC.
| ATM.145 |
Level: UI-ERROR
Short Syntax: ATM.145 Frame recvd while disconn pending, nt network ID, hndl= handle
Long Syntax: ATM.145 Frame received while disconnect pending, on network network ID, handle = handle
Description: A frame was received when the VCC was in disconnect pending.
| ATM.146 |
Level: UE-ERROR
Short Syntax: ATM.146 No prefix set, nt network ID
Long Syntax: ATM.146 The switch never set its prefix on network network ID
Description: The ATM switch never set its prefix.
| ATM.147 |
Level: UI-ERROR
Short Syntax: ATM.147 No mem to rd adptr addr, nt network ID
Long Syntax: ATM.147 No memory at init to read adapter address, on network network ID
Description: No memory available at initialization to read adapter address.
| ATM.148 |
Level: UI-ERROR
Short Syntax: ATM.148 No mem to rd adptr addr, nt network ID
Long Syntax: ATM.148 No memory at init to read adapter address, on network network ID
Description: No memory available at initialization to read adapter address.
| ATM.153 |
Level: UI-ERROR
Short Syntax: ATM.153 Timer re-entrancy err, nt net_no, flag = flag, log pt = log_point
Long Syntax: ATM.153 Timer re-entrancy error on net net_no, flag = flag, logpoint = log_point
Description: Timer re-entrancy error.
| ATM.154 |
Level: C-INFO
Short Syntax: ATM.154 Timer set alarm, nt net_no, ndx = index, callback = user_ptr
Long Syntax: ATM.154 Timer set alarm on net net_no, index = index, callback address = user_ptr
Description: Timer set.
| ATM.155 |
Level: C-INFO
Short Syntax: ATM.155 Timer set alarm, nt net_no, type = type, element = element
Long Syntax: ATM.155 Timer set alarm on net net_no, type = type, element address = element
Description: Timer set.
| ATM.156 |
Level: C-INFO
Short Syntax: ATM.156 Timer trace, nt net_no, log pt = logpoint, rc = rcode
Long Syntax: ATM.156 Timer trace on net net_no, logpoint = logpoint, return code = rcode
Description: Timer trace.
| ATM.157 |
Level: C-INFO
Short Syntax: ATM.157 Timer trace, nt net_no, log pt = logpoint, ndx = index, element = element
Long Syntax: ATM.157 Timer trace on net net_no, logpoint = logpoint, index = index, element = element
Description: Timer trace.
| ATM.158 |
Level: UI-ERROR
Short Syntax: ATM.158 Timer already stopped, nt net_no, log pt = logpoint, ndx = index, element = element
Long Syntax: ATM.158 Timer already stopped on net net_no, logpoint = logpoint, index = index, element = element
Description: Timer already stopped.
| ATM.159 |
Level: UI-ERROR
Short Syntax: ATM.159 User stopping unowned timer, nt net_no, stopper = stopper, owner = owner
Long Syntax: ATM.159 User stopping unowned timer on net net_no, stopper = stopper, owner = owner
Description: User trying to stop another user's timer.
| ATM.160 |
Level: C-INFO
Short Syntax: ATM.160 Timer cancel alarm, nt net_no, logpt = logpoint, callback = callback
Long Syntax: ATM.160 Timer cancel alarm on net net_no, logpoint = logpoint, callback address = callback
Description: Timer canceled.
| ATM.161 |
Level: UI-ERROR
Short Syntax: ATM.161 Timer SNO, nt net_no, logpt = logpoint
Long Syntax: ATM.161 Timer should not occur on net net_no, logpoint = logpoint
Description: Timer element not first, last, or middle.
| ATM.162 |
Level: C-INFO
Short Syntax: ATM.162 Timer tick, nt net_no, logpt = logpoint, tim = time, callback = callback
Long Syntax: ATM.162 Timer tick on net net_no, logpoint = logpoint, time = time, callback address = callback
Description: Timer tick.
| ATM.163 |
Level: UI-ERROR
Short Syntax: ATM.163 Timer out of elements, nt net_no
Long Syntax: ATM.163 Timer out of elements on net net_no
Description: Timer out of elements.
| ATM.164 |
Level: UI-ERROR
Short Syntax: ATM.164 Timer tried to free twice, nt net_no
Long Syntax: ATM.164 Timer tried to free twice on net net_no
Description: Timer tried to free twice.
| ATM.165 |
Level: UI-ERROR
Short Syntax: ATM.165 Tmr elmnts set to max, nt net_no
Long Syntax: ATM.165 Number of timer elements capped at maximum on net net_no
Description: The number of timer elements would have exceeded the maximum and was capped.
| ATM.166 |
Level: UI-ERROR
Short Syntax: ATM.166 VNET Registration Failed, nt network id, rc stat
Long Syntax: ATM.166 VNET User Registration Failed, on network network id, status = stat
Description: atm_vnet_init User Registration Failed
| ATM.167 |
Level: UI-ERROR
Short Syntax: ATM.167 Addr state change, not in API, nt network ID, addr address, state = state
Long Syntax: ATM.167 ATM address state change, not in API, on network network ID, ATM address = address, state= state,
Description: Address state change but API has no record of it.
| ATM.168 |
Level: UI-ERROR
Short Syntax: ATM.168 Addr in use, but not in API, nt network ID, addr address
Long Syntax: ATM.168 ATM address in use for ILMI, but not API, on network network ID, ATM address = address
Description: ILMI thinks address is registered but API has no record of it.
| ATM.169 |
Level: UI-ERROR
Short Syntax: ATM.169 No bfr to splice VCC, nt network ID, vpi1- vci1 to vpi2- vci2
Long Syntax: ATM.169 No buffer to splice VCC on network network ID, vpi1- vci1 to VCC vpi2- vci2
Description: No buffer was available to splice two VCCs.
| ATM.170 |
Level: UI-ERROR
Short Syntax: ATM.170 nt network ID, VCC vpi1- vci1 was spliced vpi2- vci2, now vpi3- vci3
Long Syntax: ATM.170 on network network ID, VCC vpi1- vci1 was spliced to vpi2- vci2, now spliced to vpi3- vci3
Description: User spliced an already spliced VCC to a different VCC.
| ATM.171 |
Level: UE-ERROR
Short Syntax: ATM.171 nt network ID, no rsp to Restart
Long Syntax: ATM.171 Switch never responded to Restart on net network ID
Description: The ATM switch never responded to Restart with RestartAck.
| ATM.172 |
Level: UI-ERROR
Short Syntax: ATM.172 Transmit msg got VCC handle, nt network ID
Long Syntax: ATM.172 Transmit message was passed NULL VCC handle on network network ID
Description: User called xmit_msg passing NULL VCC handle.
| ATM.173 |
Level: UI-ERROR
Short Syntax: ATM.173 nt network ID, cmd failed, unsupported protocol: prt
Long Syntax: ATM.173 on network network ID, cmd failed, unsupported protocol: prt
Description: An internal routine attempted to add or delete a multicast address for an unsupported protocol.
| ATM.174 |
Level: UI-ERROR
Short Syntax: ATM.174 nt network ID, cmd failed, protocol prt, error code: err
Long Syntax: ATM.174 on network network ID, cmd failed, protocol prt, error code: err
Description: An internal error occured while attempted to add or remove a multicast address.
| ATM.175 |
Level: UI-ERROR
Short Syntax: ATM.175 nt network ID, SVC msg drop, low bfrs: D2 D3 D4 D5
Long Syntax: ATM.175 on network network ID, SVC message dropped, adapter low on buffers: D2 D3 D4 D5
Description: Signaling message dropped because adapter low on buffers.
| ATM.176 |
Level: UI-ERROR
Short Syntax: ATM.176 nt network ID, disc conn hndl caller, caller handle dereg
Long Syntax: ATM.176 on network network ID, disconnect call for handle caller, caller handle already deregistered
Description: Disconnect call received but caller already deregistered
| ATM.177 |
Level: UI-ERROR
Short Syntax: ATM.177 Function vccmgrHandle called, bad vccmgr hndl caller
Long Syntax: ATM.177 Function vccmgrHandle called with invalid vccmgr handle caller
Description: VCC manager function called with invalid VCC manager handle
| ATM.178 |
Level: UI-ERROR
Short Syntax: ATM.178 Function mecHandle called, bad MEC hndl caller
Long Syntax: ATM.178 Function mecHandle called with invalid MEC handle caller
Description: An invalid MEC handle was found by VCC manager
| ATM.179 |
Level: UI-ERROR
Short Syntax: ATM.179 Function caller called, no mem
Long Syntax: ATM.179 Function caller called, out of memory
Description: ATM API call failed, no memory available
| ATM.181 |
Level: C-INFO
Short Syntax: ATM.181 VCCMGR, als new entry, vccmgr hndl vccmgrHandle
Long Syntax: ATM.181 VCCMGR, new VCC entry created dynamically, vccmgr handle = vccmgrHandle
Description: vccmgrGetVCCTableEntry called with a new VCC entry allocated dynamically from system memory
| ATM.182 |
Level: C-INFO
Short Syntax: ATM.182 VCCMGR, new VCC entry, vccmgr hndl vccmgrHandle
Long Syntax: ATM.182 VCCMGR, new VCC entry created, vccmgr handle = vccmgrHandle
Description: vccmgrGetVCCTableEntry called with a new VCC entry
| ATM.183 |
Level: C-INFO
Short Syntax: ATM.183 VCCMGR, fvs vcc entry, vccmgr hndl vccmgrHandle
Long Syntax: ATM.183 VCCMGR, free VCC entry to system, vccmgr handle = vccmgrHandle
Description: vccmgrFreeVCCTableEntry called to free VCC entry to system memory
| ATM.184 |
Level: C-INFO
Short Syntax: ATM.184 VCCMGR, free VCC entry, vccmgr hndl vccmgrHandle
Long Syntax: ATM.184 VCCMGR, free VCC entry to free list, vccmgr handle = vccmgrHandle
Description: vccmgrFreeVCCTableEntry called to free VCC entry to free list
| ATM.185 |
Level: UI-ERROR
Short Syntax: ATM.185 VCCMGR, duplicate entry, pType pType, vccmgr hndl vccmgrHandle
Long Syntax: ATM.185 VCCMGR, duplicated VCC entry in list, protocol type pType, vccmgr handle = vccmgrHandle
Description: vccmgrAddVCCToVCCList called for duplicated VCC entry in list
| ATM.186 |
Level: C-INFO
Short Syntax: ATM.186 VCCMGR, add entry, pType pType, vccmgr hndl vccmgrHandle
Long Syntax: ATM.186 VCCMGR, add VCC entry to VCC list, protocol type pType, vccmgr handle = vccmgrHandle
Description: vccmgrAddVCCToVCCList called to add VCC entry to the VCC list
| ATM.187 |
Level: C-INFO
Short Syntax: ATM.187 VCCMGR, delete entry, pType pType, vccmgr hndl vccmgrHandle
Long Syntax: ATM.187 VCCMGR, delete VCC entry from VCC list, protocol type pType, vccmgr handle = vccmgrHandle
Description: vccmgrDeleteEntryFromVCCList called to delete a VCC entry
| ATM.188 |
Level: C-INFO
Short Syntax: ATM.188 VCCMGR, new MEC entry, mec hndl mecHandle
Long Syntax: ATM.188 VCCMGR, new MEC entry created, mec handle = mecHandle
Description: vccmgrGetMECTableEntry called with a new MEC entry
| ATM.189 |
Level: C-INFO
Short Syntax: ATM.189 VCCMGR, free MEC entry, mec hndl mecHandle
Long Syntax: ATM.189 VCCMGR, free MEC entry, mec handle = mecHandle
Description: vccmgrFreeMECTableEntry called to free a MEC entry
| ATM.190 |
Level: UI-ERROR
Short Syntax: ATM.190 VCCMGR, duplicate MEC entry, mec hndl mecHandle
Long Syntax: ATM.190 VCCMGR, duplicated entries in MEC list, mec handle = mecHandle
Description: vccmgrAddMECEntryToMECList called with duplicated MEC entry
| ATM.191 |
Level: C-INFO
Short Syntax: ATM.191 VCCMGR, add MEC entry, mec hndl mecHandle
Long Syntax: ATM.191 VCCMGR, add MEC entry to MEC list, mec handle = mecHandle
Description: vccmgrAddMECEntryToMECList called with duplicated MEC entry
| ATM.192 |
Level: C-INFO
Short Syntax: ATM.192 VCCMGR, delete MEC entry, mec hndl mecHandle
Long Syntax: ATM.192 VCCMGR, delete MEC entry from MEC list, mec handle = mecHandle
Description: vccmgrDeleteMECEntryFromMECList called to delete MEC entry
| ATM.193 |
Level: C-INFO
Short Syntax: ATM.193 VCCMGR, VCC sharing, nt network ID, conn hndl connHandle
Long Syntax: ATM.193 VCCMGR, place call VCC sharing, on network network ID, conn Handle = connHandle
Description: vccmgrPlaceCall called with sharing VCC
| ATM.194 |
Level: C-INFO
Short Syntax: ATM.194 VCCMGR, place call ack, vccmgr hndl vccmgrHandle, conn hndl connHandle
Long Syntax: ATM.194 VCCMGR, place call ack, vccmgr handle = vccmgrHandle, conn handle = connHandle
Description: vccmgrPlaceCallAck called
| ATM.195 |
Level: C-INFO
Short Syntax: ATM.195 VCCMGR, place call ack for shared vcc, conn hndl vccmgrHandle
Long Syntax: ATM.195 VCCMGR, place call ack for shared VCC, conn handle = vccmgrHandle
Description: vccmgrPlaceCallAckSimulation called
| ATM.196 |
Level: C-INFO
Short Syntax: ATM.196 VCCMGR, VCC sharing, conn hndl connHandle
Long Syntax: ATM.196 VCCMGR, receive call VCC sharing, conn Handle = connHandle
Description: vccmgrReceiveCallAck called with sharing VCC
| ATM.197 |
Level: C-INFO
Short Syntax: ATM.197 VCCMGR, frame drop, id dmuxID conn hndl connHandle
Long Syntax: ATM.197 VCCMGR, data frame dropped, dmux id = dmuxID, conn Handle = connHandle
Description: vccmgrReceiveFrame called for frame drop
| ATM.198 |
Level: C-INFO
Short Syntax: ATM.198 VCCMGR, ready indicate rcvd, conn hndl connHandle
Long Syntax: ATM.198 VCCMGR, first LE ready indicate received, conn Handle = connHandle
Description: vccmgrReceiveFrame called for receiving the first ready indicate
| ATM.199 |
Level: C-INFO
Short Syntax: ATM.199 VCCMGR, duplicate VCC found, MEC hndl mecHandle, conn hndl connHandle
Long Syntax: ATM.199 VCCMGR, duplicate VCC found, MEC handle = mecHandle, conn handle = connHandle
Description: vccmgrReceiveFrame called for duplicated VCC
| ATM.200 |
Level: C-INFO
Short Syntax: ATM.200 VCCMGR, data frame rcvd, marker marker
Long Syntax: ATM.200 VCCMGR, LE data frame received, marker = marker
Description: vccmgrReceiveFrame called for receiving data frame
| ATM.201 |
Level: C-INFO
Short Syntax: ATM.201 VCCMGR, control frame rcvd, opcode opCode
Long Syntax: ATM.201 VCCMGR, LE control frame received, opCode = opCode
Description: vccmgrReceiveFrame called for receiving control frame
| ATM.202 |
Level: C-INFO
Short Syntax: ATM.202 VCCMGR, frame drop, dmuxID opCode
Long Syntax: ATM.202 VCCMGR, frame dropped, user not found, dmuxID = opCode
Description: vccmgrReceiveFrame called for dropping frame
| ATM.203 |
Level: C-INFO
Short Syntax: ATM.203 VCCMGR, simulating rcvd call, hndl connHandle
Long Syntax: ATM.203 VCCMGR, simulating receive call, connHandle = connHandle
Description: vccmgrSimulatingReceiveCall called
| ATM.204 |
Level: C-INFO
Short Syntax: ATM.204 VCCMGR, call simulated, hndl connHandle
Long Syntax: ATM.204 VCCMGR, receive call simulated, connHandle = connHandle
Description: vccmgrSimulatingReceiveCall called
| ATM.205 |
Level: C-INFO
Short Syntax: ATM.205 VCCMGR, share VCC data path, vcc hndl vccHandle
Long Syntax: ATM.205 VCCMGR, share VCC data path, vccHandle = vccHandle
Description: vccmgrOpenVccDataPath called
| ATM.206 |
Level: C-INFO
Short Syntax: ATM.206 VCCMGR, close shared VCC data path, vcc hndl vccHandle
Long Syntax: ATM.206 VCCMGR, close shared VCC data path, vcc handle = vccHandle
Description: vccmgrOpenVccDataPath called
| ATM.207 |
Level: C-INFO
Short Syntax: ATM.207 VCCMGR, hangup call by vccmgr, conn hndl vccHandle
Long Syntax: ATM.207 VCCMGR, hangup call by vccmgr, conn handle = vccHandle
Description: vccmgrReleaseVCC called to hangup call
| ATM.208 |
Level: C-INFO
Short Syntax: ATM.208 VCCMGR, nt network ID, hangup call, conn hndl connHandle
Long Syntax: ATM.208 VCCMGR, network network ID, VCC hangup call, connHandle = connHandle
Description: vccmgrHangupCall called
| ATM.209 |
Level: C-INFO
Short Syntax: ATM.209 VCCMGR, nt network ID, hangup shared call, conn hndl connHandle
Long Syntax: ATM.209 VCCMGR, network network ID, hangup shared VCC call, connHandle = connHandle
Description: vccmgrHangupCall called
| ATM.210 |
Level: C-INFO
Short Syntax: ATM.210 VCCMGR, new owner, vccmgr hndl vccmgrHandle, conn hndl connHandle
Long Syntax: ATM.210 VCCMGR, new VCC owner found, vccmgrHandle = vccmgrHandle, connHandle = connHandle
Description: vccmgrSetNewVccOwner called
| ATM.211 |
Level: C-INFO
Short Syntax: ATM.211 VCCMGR, new owner, vccmgr hndl vccmgrHandle, conn hndl connHandle
Long Syntax: ATM.211 VCCMGR, new VCC owner found, vccmgrHandle = vccmgrHandle, connHandle = connHandle
Description: vccmgrDisconnectCallSharedUser called
| ATM.212 |
Level: C-INFO
Short Syntax: ATM.212 VCCMGR, disconnect call, vccmgr hndl vccmgrHandle, conn hndl connHandle
Long Syntax: ATM.212 VCCMGR, disconnect call, vccmgr handle = vccmgrHandle, connHandle = connHandle
Description: vccmgrDisconnectCall called
| ATM.213 |
Level: C-INFO
Short Syntax: ATM.213 VCCMGR, close call sap, sap hndl vccmgrHandle
Long Syntax: ATM.213 VCCMGR, close call sap, sap handle = vccmgrHandle
Description: vccmgrCloseCallSap called
| ATM.214 |
Level: C-INFO
Short Syntax: ATM.214 VCCMGR, disconnect shared call, conn hndl connHandle
Long Syntax: ATM.214 VCCMGR, disconnect call for shared users, connHandle = connHandle
Description: vccmgrDisconnectCallSharedUser called
| ATM.215 |
Level: C-INFO
Short Syntax: ATM.215 VCCMGR, simulating hangup call, conn hndl connHandle
Long Syntax: ATM.215 VCCMGR, simulating hangup call for shared users, connHandle = connHandle
Description: vccmgrHangupCallSimulation called
| ATM.216 |
Level: UI-ERROR
Short Syntax: ATM.216 API, invalid bound VCC hndl, nt network ID, hndl handle bnd hdnl bound
Long Syntax: ATM.216 API called with invalid VCC handle, on network network ID, handle = handle bound handle = bound
Description: Invalid bound VCC handle in VCC handle passed to API
| ATM.217 |
Level: UI-ERROR
Short Syntax: ATM.217 C_caller, hangup leaf: dup caller on MP call, nt network ID, conn hndl connHandle
Long Syntax: ATM.217 C_caller, hangup leaf: duplicate caller on multipoint call, on network network ID, conn handle = connHandle
Description: Add-party received for a multipoint call for the same caller
| ATM.218 |
Level: U-INFO
Short Syntax: ATM.218 Function function_name: Grp-snd cncld nt network ID group groupHandle
Long Syntax: ATM.218 Function function_name: Group-send canceled on network network ID group groupHandle
Description: Group list(s) was modified during group-send (canceled).
| ATM.219 |
Level: CI-ERROR
Short Syntax: ATM.219 Function function_name: Grp not in use nt network ID iorb iorbp
Long Syntax: ATM.219 Function function_name: Group not in use on network network ID iorb iorbp
Description: Sending on a group and the group status was not set properly.
| Panic atmmem |
Short Syntax: ATM interface initialization failed, no memory.
Description: The ATM interface failed to allocate sufficient memory to complete initialization.
Action: Contact your customer service representative.